---
title: "SIM Replacement Instructions"
description: "Replace the SIM card in your device."
url: "https://docs.zentracloud.io/l/en/article/rsutkbrpcm-install-sim-card"
category: "Update Hardware"
updated_at: "2026-08-05T20:42:44Z"
language: "en"
---

# SIM Replacement Instructions

#### Replace the SIM

##### ZL6 / EM60G / EM50G

Steps

1. **Power off**
   
   1. Remove the batteries from the data logger to power it down.
2. **Unscrew the board**
   
   1. Remove the four screws from the main board and flip it over.
3. **Remove the SIM**
   
   1. Slide the cover to the left to open the SIM tray.
   2. Pull the SIM out of the tray.
4. **Install the new SIM**
   
   1. Insert the new SIM into the tray with the gold or silver panel facing up. Make sure the SIM is touching the edge of the tray.
   2. Close the SIM tray and slide the SIM cover to the right to secure it closed. It should click into place.
5. **Secure the board**
   
   1. Turn the main board back over.
   2. Replace the screws.
6. **Power on**
   
   1. Replace the batteries to power the data logger back on.

[Embedded iframe](//fast.wistia.net/embed/iframe/06vld0x32p)

##### ATMOS 41W

Steps

1. **Remove the funnel**
   
   1. Push down and rotate the funnel counter-clockwise.
2. **Power off**
   
   1. Unscrew the battery cap and remove the battery pack.
   2. Gently unplug the battery pack wire.
3. **Remove assembly**
   
   1. Unscrew the rain gauge assembly
   2. Turn the assembly on it's side
4. **Remove the SIM**
   
   1. Push in on the SIM to release it.
5. **Install new SIM**
   
   1. Push the new SIM card into the slot to install it.

* * *

#### Update the device configuration

##### ZL6 / EM60G

Use the[](/l/en/article/d59m50oali-module-swap-wizard) [SIM Swap Wizard](/l/en/article/0cqnn1yfj7-sim-swap-wizard) in **ZENTRA Utility Mobile** to update the settings in your device. The tool will check the hardware configuration, configure the cellular settings, and verify the connection to ZENTRA Cloud.

If the desktop version of ZENTRA Utility is the only one you have access to, you can configure the SIM manually from the terminal window. See [Module and SIM Update Guides](https://docs.zentracloud.io/l/en/article/j1i1nyuts9-module-sim-swap-guides) to find the guide for your network.

##### EM50G

**Follow these instructions for updating the configuration of the METER-supplied H-1 SIM in the Em50G data logger. Each SIM card ID is associated with a single EM50G serial number. Always install the SIM with its associated data logger or your service may be unexpectedly interrupted.**

The SIM Swap Wizard does not support the EM50G. Update the configuration from the terminal using the steps below.

Requirements:

- **Firmware** version **2.29** or later.

Show Terminal Commands Steps

1. **Connect**
   
   1. Connect via a cabled connection (Desktop).
2. **Terminal**
   
   1. Click **Window**, and select **Show Terminal**.
3. **Set the Access Point Name or APN**
   
   1. Type `set -apn h.meter.apn` and click **Send**.
   2. The response in the terminal should be "OK".
   3. Type `get -apn` to verify the setting has been updated.
   4. The response in the terminal should be "h.meter.apn".
4. **Test**
   
   1. Disconnect the logger from ECH2O Utility and then re-connect.
   2. Run a communication test to verify connectivity with the network.
   3. Click **Test**, or click **Actions** in the **Menu** bar, then **Communication test**.
